Home chevron_right Products chevron_right FIM-S222 (DISCONTINUED)

FIM-S222 (DISCONTINUED)

The FIM-S222 optical fiber interface allows one or two digital matrix intercom user panels, interface modules or 4-wire sources to be remotely connected to Eclipse, Eclipse HX and Matrix +3 intercom systems over optical fiber. A pair of FIM-S222 interfaces is required for each fiber link; one at the matrix frame and the other at the matrix user panel. See FIM-4W2 as a replacement for the FIM-S222.

Details

For use with Eclipse HX Digital Matrix systems
Interfaces with one or two digital matrix panels
Highly secure connections
24-bit digital DEMUX
48kHz audio sampling rate
Sends and receives RS-422 control data
Flat frequency response up to 20kHz, S/N >80dB
Up to 20km (12 miles) range with fiber using single mode
Up to 5km (3 miles) using multi-mode fiber
Works in demanding environmental conditions
RJ45 connectors for direct connection with matrix panels, frames and interfaces
Can be used to extend any line level 4-wire audio signal / RS-422 signal
Can be used with the earlier FIM-102D but the audio will require 5dB of gain.
Can be used with the FIM-1222 Fiber cards

Item Code

FIM-S222

Technical
Specifications

Audio

Transmission Method: Digital, TDM, 24-bit, 48k samples/sec

Input Impedance: 600 Ohms, balanced

Output Impedance: 30 Ohms, balanced

Maximum Input Level (600 Ohms): +18dBm (peak)

Maximum Output Level (from 30 Ohms): +18dBm into 600 Ohms

Frequency Response (@0dBm from 50Hz to 15kHz): ±0.2 dB

Total Harmonic Distortion + Noise: from 20Hz to 20kHz @ +8dBm, <0.2% at 1kHz @ +18dBm, <0.007%

CMRR (Common Mode Rejection Ratio): ±55db @ 1kHz

Signal to Noise Ratio: unweighted, 20Hz - 20kHz, ref. to +18dBm clip level, >80dB

Aggregate Digital Data Rate: 147.456 MB

Electro-Optical System Margin Data

Operating Wavelength: 1300nm

TX output into cable: -8 to -15dBm

RX sensitivity: =31dBm

OP Margin Single Mode: 19dBm

OP Margin Multi Mode: 12dBm

Matrix Data Communications (Frame-to-Panel Digital Data)

Transmission Rate

RS-422, Balanced TTL Levels: 0 to 150 kBits/sec

Jitter: 1.12 msec* *Higher rates possible dependent upon user system jitter tolerance

Connectors

Connectors: RJ-45, coaxial

Optical Connectors: ST-type

Power Connector: 2.5mm Circular

Power Supply

Input Voltage Range: 9-18V DC

Power Consumption: @13.8V per end, all channels at full level; <5 watts

A/C Adapter: Supplied

Temperature

Operating: -40° - +149°F (-40° - +65°C)

Humidity: 0 – 95%, non-condensing

Dimensions

7.1 x 3.3 x 1.1in (WxHxD)

(180.3 x 83.8 x 27.9mm)

Weight

0.5lbs (0.23kg)

Resources

View All

trending_flat

FIM-S222 Datasheet

2015-03

Associated
Products

FIM-4W2

The FIM-4W2 optical fiber interface allows one or two digital matrix intercom user panels, interface modules or 4-wire sources to be remotely connected to Eclipse, Eclipse HX and Matrix +3 intercom systems over optical fiber. A pair of FIM-S222 interfaces is required for each fiber link; one at the matrix frame and the other at the matrix user panel.